Author |
Message |
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Wallisville, first try at editing
Watch in hd.
Song is Slaid Cleaves- Below
Please excuse the last 30 seconds or so, it goes to black because I didn't cut the song at the end of the video. At least you can listen to the entire song.
|
Thu Apr 03, 2014 2:42 pm |
|
|
North LA Hunter
MMT Elite Member
Joined: Mon Aug 02, 2010 8:39 pm Posts: 6976 Location: West Monroe, LA
|
Re: Wallisville, first try at editing
Nice video! Thanks for sharing!
Sent from my beeper
|
Thu Apr 03, 2014 3:03 pm |
|
|
baron von
MMT 1000 Club
Joined: Tue Jan 21, 2014 2:52 pm Posts: 2806 Location: Minnesota
|
Re: Wallisville, first try at editing
awesome footage
_________________ that's going itch when it dries
|
Thu Apr 03, 2014 3:37 pm |
|
|
mudslut
MMT 1000 Club
Joined: Mon Dec 06, 2010 6:54 pm Posts: 2061 Location: Natchitoches,La
|
Re: Wallisville, first try at editing
Nice video. Got a few questions. Is that a trash can in the boat? And how do you make that cup holder?
Sent from my iPhone using Smoke Signals
_________________ 1646 Gatortail dragging a stage 1 GTR
|
Thu Apr 03, 2014 5:47 pm |
|
|
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Re: Wallisville, first try at editing
Yes it is a trash can, intention was for if I caught a mess of cats. Which sadly didn't happen.
The cup holder is pretty African -engineered. But it's 3.5 OD PVC with a cap. I dremeled out the whole and used some steel putty to keep it on and cover the small gaps.
What I did not realize is I did all the work with it trimmed down in my garage. If I trim up it raises the plate. Doesn't effect trimming and won't hurt the plastic price but it looks kinds funny. It holds a beer in cuzi perfect.
|
Thu Apr 03, 2014 6:17 pm |
|
|
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Re: Wallisville, first try at editing
The downside to putting a beer on a MM is it gets shaken to death. Ends up either flat or empty lol. I usually don't let that happen.
It could be tweaked to fit better but I'm really not concerned. It does what I want .
|
Thu Apr 03, 2014 6:22 pm |
|
|
txkingfisher
MMT 1000 Club
Joined: Fri Apr 26, 2013 1:09 am Posts: 1121 Location: SETX
|
Re: Wallisville, first try at editing
Was this run pre-gatorglide? If not, how did it hold up after sliding over a few logs?
_________________ 13' Jefferson fiberglass skiff - 14 Copperhead
|
Thu Apr 03, 2014 6:24 pm |
|
|
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Wallisville, first try at editing
It did great, didn't hit any dried logs though. I had my boy so really didn't do nothing wild, there were plenty of times I could have gone over much bigger/further emerged logs. Miller had 2-4" the trail from the miller cut to Charlotte in places was 6" or so.( I've only ran it twice so basically it was lower than the last time)
I'd like to find done veggies to try the GG on.
|
Thu Apr 03, 2014 6:45 pm |
|
|
txkingfisher
MMT 1000 Club
Joined: Fri Apr 26, 2013 1:09 am Posts: 1121 Location: SETX
|
Re: Wallisville, first try at editing
Like this? That was miller cut the summer before last. Alligator weed like a mofo!
_________________ 13' Jefferson fiberglass skiff - 14 Copperhead
|
Thu Apr 03, 2014 6:48 pm |
|
|
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Re: Wallisville, first try at editing
That's crazy!
|
Thu Apr 03, 2014 6:51 pm |
|
|
Team Schmo
MMT F.E.
Joined: Sun Sep 08, 2013 8:05 pm Posts: 814 Location: Montana
|
Re: Wallisville, first try at editing
Cool video!!
_________________ You can't fix stupid
"As long as the dog hits the water"
" Endorsed by Drake Waterfowl, Dakota Decoy, and Rig 'em Right Waterfowl"
"Stealthcraft Boats Pro Staff"
|
Thu Apr 03, 2014 6:52 pm |
|
|
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
Re: Wallisville, first try at editing
Thanks y'all!
|
Thu Apr 03, 2014 7:56 pm |
|
|
|