| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| running other brand surface drives on go-devil boats? http://mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=20721 |
Page 1 of 1 |
| Author: | JGUT [ Sat Aug 06, 2011 8:34 pm ] |
| Post subject: | running other brand surface drives on go-devil boats? |
anyone running anything other than go-devil engines on a go-devil hull. im not nocking go-devil, just wondering how well the others do on thier hulls. thanks for any info. |
|
| Author: | Gigafowl [ Sat Aug 06, 2011 8:51 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
The longer shaft designed MMs do well on a GD hull like MB GT GD... The PD does not favor the rolled rear transom design used by GD hulls and the transom angle is off a bit from the optimal PD transom angle... |
|
| Author: | Woodiebuster [ Sat Aug 06, 2011 8:52 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
Any motor you can imagine has been put on a 16x44 Go-Devil. It will get you to the blind and back but it's best to match hulls and motors. |
|
| Author: | garrettpearce [ Sat Aug 06, 2011 8:55 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
i think craig has one with a gtr on it |
|
| Author: | cb5331 [ Sat Aug 06, 2011 8:59 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
We put a 27pd on a 1644 last weekend. It runs aight. Def not the best match, but it works. |
|
| Author: | SammyC [ Sun Aug 07, 2011 5:42 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
I have a 1644 GD round chine that ran 25 w a load 27 one time w my gdsd. My MB hyperdrive ran32 w me and 27-28 w load. My MB sport runs 27-28 w a load also but don't know about no load yet. Turns awesome but would like bigger ride |
|
| Author: | nick825 [ Mon Aug 08, 2011 2:40 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
i have had quite a success with my 36 prodrive on my 16'x48'' go devil boat... the only thing i had to do is weld two tabs on the back of the boat to keep it from riding on the angled part of the boat wherethe transom and the floor meet .... |
|
| Author: | Burch [ Mon Aug 08, 2011 3:48 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
18x38 GD boat with 36 Prodrive.Works for me. |
|
| Author: | rebbeer [ Wed Aug 10, 2011 8:34 am ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
I had a 16x44 GD with a 31 MB Balanced Hyper on it and I had no complaints. I was running in the mid to upper 20's. I added wedges to the bottom of the boat and it really helped with the back end squatting while running. After the wedges, I was bumping 30. I know wedges don't solve the squatting problems on all boats, but from what I've seen, the 16x44 is a good candidate for them. |
|
| Author: | SMELVIN [ Wed Aug 10, 2011 1:38 pm ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
Team Camo used to run a MB on a GD boat and it did good when his motor would run. lol Sorry Rob i had a Bobby moment |
|
| Author: | swampmonkey [ Mon Aug 15, 2011 10:56 am ] |
| Post subject: | Re: running other brand surface drives on go-devil boats? |
i run a gtr 35 on a gd 1656 - runs great & very happy w/ setup overall. high transom model on hull & engine. get a little porpoising w/ light load & by myself, but nothing horrible - move weight or trim down a bit. had a friend that thought the engine should be mounted a touch higher b/c there's tiny bit of spray from the belt drive housing, but i think it's fine. brand new & empty, hit ~29. me & friend & normal hunt load ~25 -and i've got round chines - slower but no sliding in turns & better mud control. if i ever get a new rig, i'd go 18', not sure on width (until i ride my friends 1860 gt). the only complaint on mix match to me is not having a single point of service. not trying to jack the thread, but i'm wondering on mud control with round chine vs stepped hull chine. i have personally felt the difference on round vs tapered - and to me, round's far, far superior. anyone? thx |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|