MudmotorTalk.com
http://mudmotortalk.com/mmt_v2/

what size mud motor do i need
http://mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=26459		 Page 1 of 1
Author:  gooseman [ Mon Feb 06, 2012 3:35 pm ]
Post subject:  what size mud motor do i need
i got a 16 48 tall side mod v rivit jon boat what size mud motor do i need i was looking at mud muddy mini 23 or 27 not shour its big or too big or dixie 23 not shour the 18 cooperhead wood be big enuff hut wit 3 guys and decoys thaks for any info
Author:  deltaduckmaster [ Mon Feb 06, 2012 4:47 pm ]
Post subject:  what size mud motor do i need
35
Author:  SCmudder7071 [ Mon Feb 06, 2012 5:10 pm ]
Post subject:  Re: what size mud motor do i need
Sell ur boat and get a true mud hull and a 35 sd. Brand is ur preference. That riveted boat won't last long and it being a mod-v will kill the capabilities of these motors
Author:  gooseman [ Mon Feb 06, 2012 9:24 pm ]
Post subject:  Re: what size mud motor do i need
i thiught about that but i dont relly run in mud im in minnesoat so i run lots of rivers sholow sander bottom and lotts of weeds in a few years i wood like to get a coustom boat but right now i have what i have. i want a motor that pushes it good but safe at the same time never ran one before or ben in one so all info would be real helpfull thanks. and i like the mud buddy but sorta scared cause of the cast alum. do people have any problems with it thats sorta y i like dixie casus its stanless
Author:  4Cody4 [ Mon Feb 06, 2012 9:26 pm ]
Post subject:  what size mud motor do i need
Where in this great state are you from?


Sent using my bag phone
Author:  Quack Stackin [ Mon Feb 06, 2012 11:11 pm ]
Post subject:  Re: what size mud motor do i need
Author:  gooseman [ Tue Feb 07, 2012 8:41 am ]
Post subject:  Re: what size mud motor do i need
new ulm minnesota ok and i think i wood lean to mud buddy but what size i want to be safe
Author:  4Cody4 [ Tue Feb 07, 2012 9:18 am ]
Post subject:  what size mud motor do i need
It depends on your current budget, loads the boat will have to carry, and speeds you want to see. There are a few of us not too far from you. You can jump in my boat with me this spring for a ride if you want. I have a 1644 and am planning on a 27 hp surface drive.

I'm in chaska, and spend a fair amount of time on the rivers.


Sent using my bag phone
Author:  eljefe [ Tue Feb 07, 2012 9:23 am ]
Post subject:  Re: what size mud motor do i need
36 pd would work on that boat no problems....being the most like an outboard i think it would be the better for your applications. And fpr aint bad either....
Author:  4Cody4 [ Tue Feb 07, 2012 9:56 am ]
Post subject:  what size mud motor do i need
This is not bad advice, if I was going with a big block or had plans to upgrade hulls I'd look at the prodrive as well.


Sent using my bag phone
Author:  Mag10 [ Tue Feb 07, 2012 10:55 am ]
Post subject:  Re: what size mud motor do i need
I ran a 27 mini on a 1648 riveted jon (no mod V)for a while. It performed OK with 1 or 2 people but if you are planning on hunting 3 people, jump to a 35. If you plan to stay with that boat reinforce the transom and don't be suprised if you see cracking and leaking issues, especially if you trailer it a lot. The mod-v will hurt your perfomance, especially with that load. As 4Cody4 said, there are a number of us in the area if you want to see/ride in some other boats. I have a 36 pd on 1748 phowler and I am in Faribault.
Author:  duramaxdiesel09 [ Tue Feb 07, 2012 2:07 pm ]
Post subject:  Re: what size mud motor do i need
I had a 1648 War Eagle with a 27 PD and I wasn't happy with performance at all. My buddy had a 36 PD on the same boat and it did the job for the duck hunting he did with it. I know another guy that has a 35 MB on the same type boat and his does fine also. His is a little quicker than the PD was.
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/