| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| Go-Devil question http://mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=44409 |
Page 1 of 1 |
| Author: | Quack N Stack [ Mon Aug 19, 2013 8:21 am ] |
| Post subject: | Go-Devil question |
Anyone have an effective way of marking the trim so that you know where to set it after being trimed all the way down? |
|
| Author: | btmannin [ Mon Aug 19, 2013 10:23 am ] |
| Post subject: | Re: Go-Devil question |
Stick time..... It'll become second nature after a while |
|
| Author: | Quack N Stack [ Mon Aug 19, 2013 6:04 pm ] |
| Post subject: | Re: Go-Devil question |
I can get it pretty close but i can never find the exact spot i had it running good at. |
|
| Author: | bbb [ Tue Aug 20, 2013 1:51 pm ] |
| Post subject: | Re: Go-Devil question |
| Author: | WhoDat88 [ Tue Aug 20, 2013 3:35 pm ] |
| Post subject: | Re: Go-Devil question |
Once you get used to it you will not need to adjust much. Your RPM's are your best gauge. |
|
| Author: | Quack N Stack [ Tue Aug 20, 2013 5:20 pm ] |
| Post subject: | Re: Go-Devil question |
The mud here isnt hard but it isnt soft either...so when i drop the EZ trim it just digs a hole and i dont go anywhere. I have to drop it almost all the way down for the prop to grab so i can get going again. |
|
| Author: | WhoDat88 [ Tue Aug 20, 2013 6:42 pm ] |
| Post subject: | Re: Go-Devil question |
| Author: | Quack N Stack [ Tue Aug 20, 2013 7:01 pm ] |
| Post subject: | Re: Go-Devil question |
Ohhh no i go looking for stuff to screw around in. Theres one cut thats pretty muddy and i run into it no problem but i cant turn around on a plane because its to narrow (tried to once but i just slid onto the bank) so i stop and turn around and play in the mud. The water is only like an inch deep and the EZ trim dosent get my prop down far enough to get me moving again. |
|
| Author: | bbb [ Tue Aug 20, 2013 7:17 pm ] |
| Post subject: | Re: Go-Devil question |
Yeah we don't have the mud over here. Sounds like you need to invest in a motor with power trim. |
|
| Author: | Quack N Stack [ Tue Aug 20, 2013 7:27 pm ] |
| Post subject: | Re: Go-Devil question |
| Author: | AKA Freshwaterkilla [ Tue Aug 20, 2013 7:40 pm ] |
| Post subject: | Re: Go-Devil question |
What a fukn idiot^^^^^^;) Sent from my iPhone using Tapatalk |
|
| Author: | calphil [ Tue Aug 20, 2013 7:44 pm ] |
| Post subject: | Re: Go-Devil question |
| Author: | Quack N Stack [ Tue Aug 20, 2013 8:02 pm ] |
| Post subject: | Re: Go-Devil question |
| Author: | netman [ Wed Aug 21, 2013 10:07 pm ] |
| Post subject: | Re: Go-Devil question |
My motor is from 2005 and when GD came out with the EZ trim they sent me one. I installed it and most of the time I like it however I never had any issues with it the way I bought it. Without the EZ trim I could get the motor down alot deeper. We don't have the mud here in Indiana/Mo/Illinois/Kentucky like in La. I found when I was running around in La I liked it without the EZ trim. Around here It works fine. |
|
| Author: | Quack N Stack [ Thu Aug 22, 2013 10:49 am ] |
| Post subject: | Re: Go-Devil question |
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|