| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| GTR reverse Caliper http://mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=46696 |
Page 1 of 1 |
| Author: | pokey79 [ Wed Oct 23, 2013 7:21 pm ] |
| Post subject: | GTR reverse Caliper |
open page and second caliper down! Doesn't this look like GTR's gen 3 caliper? http://www.hayesbrake.com/markets/specialty/products/ |
|
| Author: | pokey79 [ Wed Oct 23, 2013 7:23 pm ] |
| Post subject: | Re: GTR reverse Caliper |
Apollo |
|
| Author: | OwenDickeson [ Wed Oct 23, 2013 8:08 pm ] |
| Post subject: | Re: GTR reverse Caliper |
Without looking at mine, they look very very similar. |
|
| Author: | 3rd Coast Killer [ Thu Oct 24, 2013 7:09 am ] |
| Post subject: | Re: GTR reverse Caliper |
Good find. The lighting looks close to the Gen2, except for where the plate bolts up. I need a new gen2 (or upgrade to gen3) |
|
| Author: | diddyduck [ Thu Oct 24, 2013 7:44 am ] |
| Post subject: | Re: GTR reverse Caliper |
looks like her...seems the pads are wearing out way to quick on the gen 3s |
|
| Author: | Bigrich [ Thu Oct 24, 2013 7:59 am ] |
| Post subject: | Re: GTR reverse Caliper |
I'm gonna say that's the one for sure!! And the pads Don't last!! And 45 bucks is way to high for a set too! |
|
| Author: | pokey79 [ Thu Oct 24, 2013 11:35 am ] |
| Post subject: | Re: GTR reverse Caliper |
yep i'm at 65 hrs and need new pads too! And before anybody says that im not squeezing tight enough that aint the problem! |
|
| Author: | cr244 [ Thu Oct 24, 2013 12:10 pm ] |
| Post subject: | Re: GTR reverse Caliper |
| Author: | Bigrich [ Thu Oct 24, 2013 12:18 pm ] |
| Post subject: | Re: GTR reverse Caliper |
Mine wore out at like 41 hrs.... And it had nothing to do with me not squeezing hard enough either! And Craig that was only place I knew where to get them was gator tail and needed some but I don't want to spend that much again! Gatortail told me that the pads wear due to angle of the motor  Find that hard to believe when it's hydraulic brakes
|
|
| Author: | OwenDickeson [ Thu Oct 24, 2013 12:53 pm ] |
| Post subject: | Re: GTR reverse Caliper |
I'll be needing a new set around 65 hours. If im doing any kind of hard reversing, I lock the lever in. |
|
| Author: | Gameover [ Thu Oct 24, 2013 1:12 pm ] |
| Post subject: | Re: GTR reverse Caliper |
i had my first set go out at 44 hours ( or atleast the one closest to motor). i have 82 hours now and i swapped the pads around to prolong life once and will get probally another 20. the problem i see if the caliber doesnt retract enough and the inner pad just barely rubs the rotor at all times. |
|
| Author: | cr244 [ Thu Oct 24, 2013 1:20 pm ] |
| Post subject: | Re: GTR reverse Caliper |
| Author: | dfou [ Thu Oct 24, 2013 1:29 pm ] |
| Post subject: | Re: GTR reverse Caliper |
| Author: | OwenDickeson [ Thu Oct 24, 2013 4:35 pm ] |
| Post subject: | Re: GTR reverse Caliper |
Mine sits like this. Then turn the rotar 180 degrees, and it sits like this. |
|
| Author: | Bigrich [ Thu Oct 24, 2013 5:21 pm ] |
| Post subject: | Re: GTR reverse Caliper |
Owen I haven't rotated mine like that but mine stays close to the rotor And gameover my inside pad wore out before my outside too |
|
| Author: | OwenDickeson [ Thu Oct 24, 2013 6:07 pm ] |
| Post subject: | Re: GTR reverse Caliper |
It's like my rotor is warped.... |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|