| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| 1751 Excel F4, motor options? http://mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=65295 |
Page 1 of 1 |
| Author: | Big_Country [ Fri Jan 08, 2016 12:17 pm ] |
| Post subject: | 1751 Excel F4, motor options? |
I currently have a Nissan 55hp outboard on it, but I think I wanna swap over to a MM. I'm leaning a lot to the GTRs. I have seen on here they have long and short, which would I need to run it on my boat? |
|
| Author: | craig [ Fri Jan 08, 2016 1:08 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
What is the transom height on the hull? You'll need to have between 19-21" for a tall transom GTR. For a short transom model GTR you need a transom with height of 15". |
|
| Author: | Big_Country [ Fri Jan 08, 2016 1:19 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
I'm not sure, I would have to measure it. I know I have to run a long shaft outboard on it. |
|
| Author: | b.latiolais [ Fri Jan 08, 2016 2:48 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
Their website says your transom should be either 17" or 20". http://excelboats.net/Shallow%20Water%20F4.html |
|
| Author: | iah2ofwlr [ Fri Jan 08, 2016 9:15 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
Might wanna see what hull it is too, viper or shallow water. I don't know personally but I hear the viper hull doesn't work the best with mm's. Need a shallow water hull. The shallow water is flat where the viper has the reverse chines. |
|
| Author: | HunterLafever [ Sat Jan 09, 2016 9:19 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
Mud Buddy only way to go on a excel in my opinon |
|
| Author: | Big_Country [ Mon Jan 11, 2016 12:42 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | Big_Country [ Mon Jan 11, 2016 12:46 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | iah2ofwlr [ Mon Jan 11, 2016 1:17 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | Big_Country [ Tue Jan 12, 2016 8:35 am ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | iah2ofwlr [ Tue Jan 12, 2016 11:23 am ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | Big_Country [ Tue Jan 12, 2016 12:15 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
| Author: | iah2ofwlr [ Tue Jan 12, 2016 1:27 pm ] |
| Post subject: | Re: 1751 Excel F4, motor options? |
I love my HD but no way would I want a sport V. If I had the money I'd get a new HDR efi with the mako 6 upgrade. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|