Author |
Message |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 18 hp mudbuddy surface drive wont start with key
Battery is new. motor will start with the pull rope but all it does when i turn the key over it just clicks. not even offering to turn over. motor has only lke 30 hrs on it.  Does anyone have any ideas what would be wrong?
|
Sun Oct 23, 2011 6:57 pm |
|
 |
cb5331
MMT Super Elite Member
Joined: Fri Dec 18, 2009 8:10 pm Posts: 16915 Location: Rowlett, TX
|
 Re: 18 hp mudbuddy surface drive wont start with key
Check your electrical connections at the battery and the starter. Probably a loose wire or a build up of corrosion. Make sure you give them a good tug as the connections could be loose inside the terminals.
|
Sun Oct 23, 2011 7:23 pm |
|
 |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 Re: 18 hp mudbuddy surface drive wont start with key
ok ya ill check that out. i hope thats all it is. is there any way that the part that wont let it start unless its out of the water could be bad? idk i had this motor on a 14' john boat and it had a problem starting unless it was at a certain angle. thought that had to do with it not sitting right on the transom. But i just put the motor on a gator trax rogue and it wnt even try to turn over.
|
Sun Oct 23, 2011 7:59 pm |
|
 |
cb5331
MMT Super Elite Member
Joined: Fri Dec 18, 2009 8:10 pm Posts: 16915 Location: Rowlett, TX
|
 Re: 18 hp mudbuddy surface drive wont start with key
The mercury switch? It would be easy to bypass so you could rule that out if needed.
Sounds like the solenoid is clicking from what you said in your first post. I believe the mercury switch would keep that from happening. Sounds to me like a bad battery or a bad connection. Your getting enough juice to open the solenoid, just don't have enough to turn the starter. I'd check all your connections first.
|
Sun Oct 23, 2011 8:02 pm |
|
 |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 Re: 18 hp mudbuddy surface drive wont start with key
ok ill give that a shot and get back with you if that doesnt fix it! thanx
|
Sun Oct 23, 2011 8:23 pm |
|
 |
torrey w
MMT Member
Joined: Thu Oct 13, 2011 8:21 pm Posts: 42 Location: mankato mn
|
 Re: 18 hp mudbuddy surface drive wont start with key
Not the mercury switch when that goes bad it does nothing no clicks. Either starter is bad or bad electrical connection mine is battery cable needs to be cleaned every so often.
And i would by pass the switch it has solved alot of headaches for me
|
Mon Oct 24, 2011 8:20 pm |
|
 |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 Re: 18 hp mudbuddy surface drive wont start with key
How do I bypass the switch? And does the switch look lk a little black cylinder? Or where is it lol
|
Tue Oct 25, 2011 8:03 pm |
|
 |
torrey w
MMT Member
Joined: Thu Oct 13, 2011 8:21 pm Posts: 42 Location: mankato mn
|
 Re: 18 hp mudbuddy surface drive wont start with key
That would be the switch. Just unplug the wires and create a jumper for the connections to run power through
|
Tue Oct 25, 2011 8:27 pm |
|
 |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 Re: 18 hp mudbuddy surface drive wont start with key
Ok I'll try that! Does anyone no where I could get a new starter if that's the case?
|
Wed Oct 26, 2011 2:58 pm |
|
 |
cb5331
MMT Super Elite Member
Joined: Fri Dec 18, 2009 8:10 pm Posts: 16915 Location: Rowlett, TX
|
 Re: 18 hp mudbuddy surface drive wont start with key
Unless you've sunk the motor, I doubt you need to replace the starter. They just don't die very often. Have you checked your connections yet? Start with the simple stuff, don't get excited and start repairing and replacing things that weren't broken in the first place.
|
Wed Oct 26, 2011 3:06 pm |
|
 |
Gauge08
MMT Member
Joined: Tue Aug 16, 2011 12:25 pm Posts: 8
|
 Re: 18 hp mudbuddy surface drive wont start with key
Thanks guys I had a bad cylanoid and now it starts like a champ! I appriciate the help!
|
Thu Oct 27, 2011 5:14 pm |
|
 |
|