MudmotorTalk.com
http://mudmotortalk.com/mmt_v2/

instructions on changing heads
http://mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=17554		 Page 1 of 1
Author:  smboudreaux [ Thu Apr 07, 2011 12:30 pm ]
Post subject:  instructions on changing heads
anyone have a link to step by step instructions on changing heads? its on a 04 mudbuddy 29. tired search and came up with zero
Author:  OwenDickeson [ Thu Apr 07, 2011 12:36 pm ]
Post subject:  Re: instructions on changing heads
unbolt heads
remove heads and clean all old gasket material
put on new gasket and bolt up new heads
put in push rods and set valve lash

I'm sure someone could go into a lot more detail but there is really no need. Changing your heads is very simple.
Author:  Bubby83 [ Thu Apr 07, 2011 3:36 pm ]
Post subject:  Re: instructions on changing heads
"set valve lash"
Can someone ellaborate on how this is done?
Author:  MaXXis85 [ Thu Apr 07, 2011 3:37 pm ]
Post subject:  Re: instructions on changing heads
Author:  caddobrook [ Thu Apr 07, 2011 4:17 pm ]
Post subject:  Re: instructions on changing heads
make sure you torque everything to spec....
Author:  Bubby83 [ Thu Apr 07, 2011 5:14 pm ]
Post subject:  instructions on changing heads
Where might I find torque specs?
Author:  OwenDickeson [ Thu Apr 07, 2011 5:22 pm ]
Post subject:  Re: instructions on changing heads
prolly a briggs manual
Author:  caddobrook [ Thu Apr 07, 2011 5:29 pm ]
Post subject:  Re: instructions on changing heads
Author:  OwenDickeson [ Thu Apr 07, 2011 6:03 pm ]
Post subject:  Re: instructions on changing heads
You might be able to download a PDF of it somewheres online.
Author:  craig [ Thu Apr 07, 2011 6:22 pm ]
Post subject:  Re: instructions on changing heads
Author:  deadbird8 [ Thu Apr 07, 2011 8:08 pm ]
Post subject:  Re: instructions on changing heads
Author:  dguidry [ Thu Apr 07, 2011 9:03 pm ]
Post subject:  Re: instructions on changing heads
Author:  OwenDickeson [ Thu Apr 07, 2011 9:04 pm ]
Post subject:  Re: instructions on changing heads
Author:  deadbird8 [ Fri Apr 08, 2011 5:43 am ]
Post subject:  Re: instructions on changing heads
Author:  Bubby83 [ Fri Apr 08, 2011 5:52 am ]
Post subject:  Re: instructions on changing heads
From what I have about 1/4" past TDC, it sounds like if you set lashing at TDC on a Van. you will actually be setting lash while the compression release is engaged.
Author:  MaXXis85 [ Fri Apr 08, 2011 6:11 am ]
Post subject:  Re: instructions on changing heads
Author:  OwenDickeson [ Fri Apr 08, 2011 7:02 am ]
Post subject:  Re: instructions on changing heads
Author:  MaXXis85 [ Fri Apr 08, 2011 7:12 am ]
Post subject:  Re: instructions on changing heads
Author:  craig [ Fri Apr 08, 2011 7:17 am ]
Post subject:  instructions on changing heads
Author:  MaXXis85 [ Fri Apr 08, 2011 7:21 am ]
Post subject:  Re: instructions on changing heads
Author:  dguidry [ Fri Apr 08, 2011 7:43 am ]
Post subject:  Re: instructions on changing heads
Just received my Briggs repair manual. Wish i'd have had it when I installed my cam and heads. It's excellent, very detailed step by step instructions on everything one can think of doing to the engine. $20 plus shipping. Get you one.
Author:  deadbird8 [ Fri Apr 08, 2011 5:58 pm ]
Post subject:  Re: instructions on changing heads
Author:  garrettpearce [ Fri Apr 08, 2011 7:15 pm ]
Post subject:  Re: instructions on changing heads
Author:  XGEN-DUCKMAN [ Fri Apr 08, 2011 7:20 pm ]
Post subject:  Re: instructions on changing heads
Lash should set when the valve is closed, past tdc or the YouTube way should work.....
Author:  XGEN-DUCKMAN [ Fri Apr 08, 2011 9:33 pm ]
Post subject:  Re: instructions on changing heads
Just finished installing my new heads and tried it both ways, didn't notice a difference...... both held at .005....
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/