MudmotorTalk.com
http://mudmotortalk.com/mmt_v2/

Has anybody put the 40hp Kohler on anytype surface drive
http://mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=26595		 Page 1 of 1
Author:  huntingsmith [ Fri Feb 10, 2012 12:52 pm ]
Post subject:  Has anybody put the 40hp Kohler on anytype surface drive
Would like to know what the performance of the Kohler ch1000 is on a mudmotor
Author:  meterman3 [ Fri Feb 10, 2012 12:55 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Mud buddy did

And I drive a pd and approve this message
Author:  odass [ Fri Feb 10, 2012 12:55 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Mud Buddy used to put the 40s on sport frames a few years ago. Never rode in one with it. But I'm sure they pushed pretty good.
Author:  BoatDR [ Fri Feb 10, 2012 1:00 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Mdubuddy and Beavertail both did. But the carburetor and governor system is a real PIA so MB quit offering them, dont know if Beavertail still does or not.


Also in a side by side comparison the 35 Briggs is virtually identical in power.
Author:  huntingsmith [ Fri Feb 10, 2012 1:04 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Been kickin the idea of building a surface drive style system w this motor w the ideas from a mud buddy and gatortail platform w a lil godevil in it. Been workin in a machine shop for the last couple months. Just an idea. I figure I could always build a badass duck plucker if it don't pan out.
Author:  BoatDR [ Fri Feb 10, 2012 1:08 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
A duck plucker with a 40hp motor..........now that is something that I would like to see.
Author:  Robn1020 [ Fri Feb 10, 2012 1:21 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Author:  deltaduckmaster [ Fri Feb 10, 2012 1:26 pm ]
Post subject:  Has anybody put the 40hp Kohler on anytype surface drive
I ran one last year on a Gtr frame it's carb sucked bad!!! As for as speed it was the same as a 35 Briggs! I found the Briggs had more bottom end power!!
Author:  huntingsmith [ Fri Feb 10, 2012 1:33 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Ideally what would be the best motor I could buy to do upgrades to in the future. I don t like the idea of aluminum heads. I see there are after markets out there by for a stock motor what would be an ideal powerhouse for a surface drive motor
Author:  wm [ Fri Feb 10, 2012 7:20 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
backwater also tried a 40hp kohler and the 35 van walked away from it i think those suck stock from what i read
Author:  radikkle [ Fri Feb 10, 2012 7:34 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
PD tried the 40 too.yo can see who won that battle.
Author:  chaseh [ Fri Feb 10, 2012 9:08 pm ]
Post subject:  Has anybody put the 40hp Kohler on anytype surface drive
From what I've heard, the generac might be the next go to motor. It's a little stouter block where it counts, and more and more aftermarket parts are showing up. Again, this is hearsay from folks actually running them.
Author:  huntingsmith [ Sat Feb 11, 2012 9:10 am ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Has anyone tried some small diesel engines?
Author:  chaseh [ Sun Feb 12, 2012 12:38 am ]
Post subject:  Has anybody put the 40hp Kohler on anytype surface drive
Author:  msm8281 [ Sun Feb 12, 2012 7:00 am ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Author:  robertb4wd [ Sun Feb 12, 2012 1:42 pm ]
Post subject:  Re: Has anybody put the 40hp Kohler on anytype surface drive
Author:  chaseh [ Tue Feb 14, 2012 5:43 pm ]
Post subject:  Has anybody put the 40hp Kohler on anytype surface drive
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/