Tapatalk 2
| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| PD RPM's http://mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=31769 |
Page 1 of 1 |
| Author: | hunterg [ Wed Aug 22, 2012 8:45 pm ] |
| Post subject: | PD RPM's |
How do i turn up my rpm's? I am only running 5500-5600 in the water and 5800-5900 out of the water on a stock 36PD. |
|
| Author: | OwenDickeson [ Wed Aug 22, 2012 8:53 pm ] |
| Post subject: | Re: PD RPM's |
Just start turning different screws. You should be around 6000 in the water atleast. |
|
| Author: | jordy [ Wed Aug 22, 2012 8:53 pm ] |
| Post subject: | Re: PD RPM's |
| Author: | med [ Wed Aug 22, 2012 8:54 pm ] |
| Post subject: | Re: PD RPM's |
Tapatalk 2 |
|
| Author: | JLACOUR [ Wed Aug 22, 2012 9:12 pm ] |
| Post subject: | Re: PD RPM's |
| Author: | Woodiebuster [ Wed Aug 22, 2012 9:21 pm ] |
| Post subject: | Re: PD RPM's |
Are you running in the low 40's? |
|
| Author: | hunterg [ Wed Aug 22, 2012 10:31 pm ] |
| Post subject: | Re: PD RPM's |
haha took me a minute to figure out why yall were ragin me! i meant 3500-3600 in water and 3800-3900 out of water. my bad! lol |
|
| Author: | med [ Wed Aug 22, 2012 11:50 pm ] |
| Post subject: | Re: PD RPM's |
Go to the back of your motor and on the right side there will be a screw with a spring around it. That will get your oow rpms up. Tapatalk 2 |
|
| Author: | OwenDickeson [ Thu Aug 23, 2012 8:44 am ] |
| Post subject: | Re: PD RPM's |
| Author: | hunterg [ Thu Aug 23, 2012 9:52 am ] |
| Post subject: | Re: PD RPM's |
alright i did all of that, i tightened that screw that med told me to and even with it all the way tight as far as it can go it's only reaching about 4150 out of water. idle is set at 1200. |
|
| Author: | OwenDickeson [ Thu Aug 23, 2012 10:01 am ] |
| Post subject: | Re: PD RPM's |
Leakdown and compression check |
|
| Author: | hunterg [ Thu Aug 23, 2012 10:15 am ] |
| Post subject: | Re: PD RPM's |
leakdown? |
|
| Author: | Will [ Thu Aug 23, 2012 10:36 am ] |
| Post subject: | Re: PD RPM's |
Leakdown? Compression test? With no load? Even if it was leaking it should hit the limit out of the water... Check to make sure your throttle is opening the carb all the way! |
|
| Author: | MaXXis85 [ Thu Aug 23, 2012 10:41 am ] |
| Post subject: | Re: PD RPM's |
| Author: | Will [ Thu Aug 23, 2012 10:47 am ] |
| Post subject: | Re: PD RPM's |
| Author: | hunterg [ Thu Aug 23, 2012 8:40 pm ] |
| Post subject: | Re: PD RPM's |
alright thanks guys for all the info! |
|
| Author: | deadbird8 [ Sat Aug 25, 2012 4:24 am ] |
| Post subject: | Re: PD RPM's |
| Author: | BlueShamu [ Sat Aug 25, 2012 8:28 am ] |
| Post subject: | Re: PD RPM's |
| Author: | fredthewelder [ Sun Sep 02, 2012 1:40 pm ] |
| Post subject: | Re: PD RPM's |
Dose any one have a pic of where that spring is located so I can see if mine is brown thnxs |
|
| Author: | BlueShamu [ Tue Sep 04, 2012 5:18 pm ] |
| Post subject: | Re: PD RPM's |
I think this is the one they are talking about...looking at the back of the motor, above the exhaust shield. DSC03563.JPG |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|