Use stock gasket and you can go .060 you will be 185/190 psi run 93 octane you will be fine as long as you are using stock rods
| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| 36 HP vanguard shaving heads ? http://mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=55872 |
Page 1 of 1 |
| Author: | Nick peltier [ Tue Aug 19, 2014 10:43 am ] |
| Post subject: | 36 HP vanguard shaving heads ? |
Has any one had problems after shaving there heads .050 on a 36 HP big block vanguard ? Like detnation or some other type of issues ? Thinking about shaving mine .050 to get some more power out of the engine also will the stock head gasket be fine or will it be best to use a copper head gasket I know copper is better but is it nessary for this type of modification ? |
|
| Author: | AKA Freshwaterkilla [ Tue Aug 19, 2014 11:11 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
If u can find a copper gasket it's better but not necessary 50 thousandths depends on what other mods u havr Sent from my iPhone using |
|
| Author: | jerimiahw [ Tue Aug 19, 2014 11:12 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
| Use stock gasket and you can go .060 you will be 185/190 psi run 93 octane you will be fine as long as you are using stock rods
|
|
| Author: | 50fps [ Tue Aug 19, 2014 11:47 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
Shaved .055, stock gaskets, 190 psi on my tester w/ stock pistons and rods running 91 octane non-ethanol unleaded with no issues. |
|
| Author: | Michaelk727 [ Sat Apr 01, 2017 8:57 pm ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
Sorry I know this is an old thread, but how much speed could I pick up by shaving the heads on my 36hp vanguard? |
|
| Author: | Will C [ Sun Apr 02, 2017 10:05 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
By only decking the heads only you will get a noticably more stronger engine with just a little bit mre top end. |
|
| Author: | Michaelk727 [ Sun Apr 02, 2017 11:20 pm ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
So my motor would perform better with a load and out of the hole? And are there any cheap mods I can do to increase top end speed? |
|
| Author: | banded-mallard [ Mon Apr 03, 2017 4:42 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
| Author: | CypressCritter [ Tue Apr 04, 2017 8:22 am ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
Carb, Heads, and exhaust will wake that puppy up! What goes in needs more space to come out=torque and speed increase! |
|
| Author: | pokey79 [ Tue Apr 04, 2017 2:27 pm ] |
| Post subject: | Re: 36 HP vanguard shaving heads ? |
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|