2012....I know of one about to be for sale.....set up on a CC rig.
| MudmotorTalk.com http://mudmotortalk.com/mmt_v2/ |
|
| most desirable year of PD in terms of reliability/performce http://mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=70447 |
Page 1 of 1 |
| Author: | JphIII [ Sat May 20, 2017 9:07 pm ] |
| Post subject: | most desirable year of PD in terms of reliability/performce |
I'm looking into buying a used 36PD and was curious as to what yall feel was the best year/configuration would be given the various generations of lower ends, changes with Briggs powerhead, electric vs. hydraulic reverse, etc. IE: if you were to go back and buy a used carbureted PD what year/generation would you be looking for if reliability and not getting stuck were your main concerns? |
|
| Author: | BlueShamu [ Sat May 20, 2017 9:29 pm ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
2012....I know of one about to be for sale.....set up on a CC rig.
|
|
| Author: | brickgw [ Sun May 21, 2017 5:41 am ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
If I were to do it again I would avoid the gen 3 lower unless you run alot of veg. Seems like the only folks who cared for the gen 3 gearing liked it for heavy vegetation. Sent from my SM-G900P using Tapatalk |
|
| Author: | WhoDat88 [ Sun May 21, 2017 6:30 pm ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
| Author: | WhoDat88 [ Sun May 21, 2017 6:31 pm ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
| Author: | wade_660 [ Sun May 21, 2017 8:40 pm ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
I like a gen 2 best besides the fact that the shafts snap like twigs and the props are hard to take off. Sent from my iPhone using Tapatalk |
|
| Author: | banded-mallard [ Mon May 22, 2017 8:20 am ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
2007 gen 2 oil filled lower, which I believe was the fastest gear ratio lower. Mine still runs like a top, although different powerhead. |
|
| Author: | BlueShamu [ Tue May 23, 2017 8:26 pm ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
| Author: | MaXXis85 [ Wed May 24, 2017 5:17 am ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
The Pro Drive frame itself id pretty darn reliable from Gen2 to current. Gen 3 is sloe from large 2:1 ratio. I know Tbubba has a Gen 4 EFI briggs for sale with headwork installed. Good motor right there. |
|
| Author: | CypressCritter [ Wed May 24, 2017 7:38 am ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
| Author: | BlueShamu [ Wed May 24, 2017 11:47 am ] |
| Post subject: | Re: most desirable year of PD in terms of reliability/perfor |
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|