| Author |
Message |
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
 11x10 prop for 23hp I have a 14hp mudbuddy mini sufacedrive.I got a 23hp vanguard to fit on the frame. Just not sure what prop to buy.
|
| Thu Mar 01, 2012 11:30 am |
|
|
|
CCC
MMT 1000 Club
Joined: Sun Jan 01, 2012 9:25 am
Posts: 1685
|
9x6 or 9x5 prop for 23hp My 23 has a 11x10
|
| Thu Mar 01, 2012 11:42 am |
|
|
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
Re: 9x6 or 9x5 prop for 23hp Well on the mudbuddy site it has a 9x5 or 9x6 fitting a 23hp vanguard.
|
| Thu Mar 01, 2012 11:47 am |
|
|
|
CCC
MMT 1000 Club
Joined: Sun Jan 01, 2012 9:25 am
Posts: 1685
|
9x6 or 9x5 prop for 23hp They might be geared diff idk
|
| Thu Mar 01, 2012 11:50 am |
|
|
|
CCC
MMT 1000 Club
Joined: Sun Jan 01, 2012 9:25 am
Posts: 1685
|
9x6 or 9x5 prop for 23hp That's long tail props the site has 11x10 for 21-29 hp motors
|
| Thu Mar 01, 2012 11:53 am |
|
|
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
Re: 9x6 or 9x5 prop for 23hp Oh okay i just dont wana buy the wrong prop.I hope a prop would work with that 23 on that frame a guy told me a regeared diff.
|
| Thu Mar 01, 2012 12:01 pm |
|
|
|
Mag10
MMT Pro Member
Joined: Wed Jan 14, 2009 12:31 pm
Posts: 342
Location: Faribault, Mn
|
Re: 11x10 prop for 23hp Check your current prop it is probably threaded. Most of the 11X10s will be hex.
|
| Thu Mar 01, 2012 12:25 pm |
|
|
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
Re: 11x10 prop for 23hp It is threaded i looked online and i found a 11x10 prop 3/4 threaded.
|
| Thu Mar 01, 2012 1:00 pm |
|
|
|
bobbyjober
MMT Addict
Joined: Sun Aug 08, 2010 3:28 pm
Posts: 546
Location: St. Martinville, La
|
Re: 11x10 prop for 23hp I did a swap from 18hp to a 24 Honda on a mini frame. I can run and do run a 12x12 GoDevil SD prop, that I had machined for 3/4-10 threaded. The gearing is lower than a 23 mini. Best bet is to try the 11x10 and see if you like the perormance, if not go from there. Hill Marine will make a 12x10, 12x11,and 12x12 in a 3/4-10 thread for an extra $50.
_________________
1542 FLATBOTTOM WITH 24 HONDA MUD BUDDY MINI TURNING A 12" GDSD PROP/17 FT XPRESS CENTER CONSOLE WITH 90 MARINER
|
| Thu Mar 01, 2012 1:19 pm |
|
|
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
Re: 11x10 prop for 23hp Yea thanks for the info i saw the 11x10 3/4 thread on hill marine also.
|
| Thu Mar 01, 2012 1:56 pm |
|
|
|
duckman223
MMT Member
Joined: Sun Feb 12, 2012 5:36 pm
Posts: 27
|
Re: 11x10 prop for 23hp How fast do you get out of your boat and how fast ya think. My boat will go i have a 14ft alumcraft weights about 135 with a 23hp mini.
|
| Thu Mar 01, 2012 1:58 pm |
|
|
|
bobbyjober
MMT Addict
Joined: Sun Aug 08, 2010 3:28 pm
Posts: 546
Location: St. Martinville, La
|
Re: 11x10 prop for 23hp My setup runs 24mph, gets on plane with a load . My old ass boat is beat to crap also, when I run against wind and current, boat pops up and feels like I gain 5 more mph.
_________________
1542 FLATBOTTOM WITH 24 HONDA MUD BUDDY MINI TURNING A 12" GDSD PROP/17 FT XPRESS CENTER CONSOLE WITH 90 MARINER
|
| Fri Mar 02, 2012 8:45 am |
|
|
|
