MudmotorTalk.com
http://mudmotortalk.com/mmt_v2/

sliding
http://mudmotortalk.com/mmt_v2/viewtopic.php?f=5&t=36453		 Page 1 of 1
Author:  green head [ Tue Jan 15, 2013 10:31 pm ]
Post subject:  sliding
well i'm tired of sliding in turns with my slick bottom. we have a couple trails on our lease that are narrow and have a lot of sharp turns.my question is is there anything i can do to help in the turns but not affect the performance in the mud.i also want to put some gator glide on it but i haven't done it yet do to the sliding.
Author:  brasso [ Tue Jan 15, 2013 10:37 pm ]
Post subject:  Re: sliding
Leannnnn!!
Author:  brasso [ Tue Jan 15, 2013 10:37 pm ]
Post subject:  Re: sliding
What type of chines does it have?
Author:  green head [ Tue Jan 15, 2013 10:38 pm ]
Post subject:  Re: sliding
square chines
Author:  CootSlayerRMFT [ Tue Jan 15, 2013 10:39 pm ]
Post subject:  Re: sliding
Gator Glide won't make it slide any more than normal unless you're in mud or on grass and logs. The only thing that's gonna help with the sliding in this context is a round chine. Other than that, tiller time! ( aka Learn how to drive you rig.)


**Sent from my Obama Phone**
Author:  brasso [ Tue Jan 15, 2013 10:40 pm ]
Post subject:  Re: sliding
Theres your problem. Sell and get a tapered or round chine.. Or just learn how to drive that one.. Ive ran the exact same types of ditches your speaking of in grand chanier and pecan island with a square chine, and ended up on land more than a few times at first.. I can now go full throttle and not miss a beat. Learn your boat.
Author:  WestEndAngler [ Tue Jan 15, 2013 10:43 pm ]
Post subject:  Re: sliding
x2 on some stick time. I've also seen some people weld square tubing to help the boat hook up but I think that's overkill.
Author:  take'emgator [ Tue Jan 15, 2013 11:24 pm ]
Post subject:  Re: sliding
In the off season flip the boat over and have a piece of 1.5" angle welded right down the center
Author:  CAJUN OUTLAW [ Tue Jan 15, 2013 11:30 pm ]
Post subject:  Re: sliding
Sliding is what a square chine flat bottom does.
u gotta slow down a lil before turning.
Common sense is just as important as stick time.
Whoever turns their square chined flat bottom without sliding,
Simply aint got much power pushing it.
Author:  brasso [ Tue Jan 15, 2013 11:31 pm ]
Post subject:  Re: sliding
Well there you are. I thought you finally slapped someone who was better at slapping, I almost started to miss you to! :lol:
Author:  CAJUN OUTLAW [ Tue Jan 15, 2013 11:45 pm ]
Post subject:  Re: sliding
Leave the thinking to someone more qualified.
Author:  CAJUN OUTLAW [ Tue Jan 15, 2013 11:47 pm ]
Post subject:  Re: sliding
Only old men , bitches , and kids get slaps....fyi.
Author:  TURBODRIVE [ Wed Jan 16, 2013 12:02 am ]
Post subject:  Re: sliding
Author:  deltaduckmaster [ Wed Jan 16, 2013 6:53 am ]
Post subject:  Re: sliding
Try the tubbing thing on the bottom I have it and it don't effect performance at all
Author:  eljefe [ Wed Jan 16, 2013 8:11 am ]
Post subject:  Re: sliding
what size boat and motor? tiller time is the key.....you will learn to work throttle and "feel" the boat grab and then back wot.....sliding is a fact of life for a square flat and minimizing it is the key.....but having said that, i still slide out and hit the bank on occassion. I dont think i will have near the trouble with sliding by dropping down to a 40" bottom, feather the prop a little and lean into turn and it should grab just fine......
Author:  CCC [ Wed Jan 16, 2013 8:13 am ]
Post subject:  Re: sliding
If the bottoms soft trim down, it seems to help
Author:  Will [ Wed Jan 16, 2013 8:18 am ]
Post subject:  Re: sliding
Turn before you get there, let the nose slide across the bank in the corner, then wot. LOL or just slow down, my 54 is like driving a skim board, theres no leaning gonna help it, let off the gas enough to feel it bite then get back in it. Tiller time, tiller time, tiller time...
Author:  mizzippi jb [ Wed Jan 16, 2013 10:06 am ]
Post subject:  Re: sliding
I had to get used to a little slide when I sold my gd hull. It ain't bad at all, just gotta get used to it and learn the feel.
Author:  lucecr [ Wed Jan 16, 2013 5:57 pm ]
Post subject:  Re: sliding
Reaction chine. No more sliding. But I don't know if Jay could add it to a boat. PM InstaGator911
Author:  green head [ Tue Jan 22, 2013 7:35 pm ]
Post subject:  Re: sliding
thanks for the info guys
i'll try trimming down next time i'm running it
Author:  eljefe [ Tue Jan 22, 2013 7:44 pm ]
Post subject:  Re: sliding
trimming down wont do shit if you dont work the throttle.....use the throttle to initiate the turn and then let off and let it grab at the turn and then wot throttle out....... your gonna have to learn your rig and know how far it takes to grab. If its real shallow it wont grab and your gonna need to know where those spots are.
Author:  AKA Freshwaterkilla [ Tue Jan 22, 2013 7:45 pm ]
Post subject:  Re: sliding
U just need a motor with more power then u can throw the front end where u want it and gas the shit out of it haah
Author:  AKA Freshwaterkilla [ Tue Jan 22, 2013 7:47 pm ]
Post subject:  Re: sliding
U just need a motor with more power then u can throw the front end where u want it and gas the shit out of it haah
Author:  take'emgator [ Tue Jan 22, 2013 9:33 pm ]
Post subject:  Re: sliding
I don't care what you got, if you are in mud you are sliding, the only thing that i have seen turn in the mud is ribbed bottom boats. Now in deeper water you have some hull designs that will slice through the water making turning a breeze (extreme, reaction chine, etc.), then you have the square chine boats that with a little practice you can make them turn very well in deep water. IN mud you can forget it, you ain't cutting corners in mud.
Author:  AKA Freshwaterkilla [ Tue Jan 22, 2013 10:51 pm ]
Post subject:  Re: sliding
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/