MudmotorTalk.com
http://mudmotortalk.com/mmt_v2/

1848 Brother Boat with 36 PD
http://mudmotortalk.com/mmt_v2/viewtopic.php?f=5&t=5445
Page 1 of 1

Author:  OwenDickeson [ Sun Oct 18, 2009 4:57 pm ]
Post subject:  1848 Brother Boat with 36 PD

MM Brand: Pro-Drive
Horsepower: 36
Boat Brand: Brothers Boats
Boat Size: 1848

Speeds | Shallow Water: Didnt Exist.
Speeds | Deep Water: 28.6
Total Boat Load With Gear Etc: Me
Conditions Tested In: Windy with choppy water

Comments: The boat is 3/16ths bottom with 21" tall 1/8" sides. 6 2x2 runners and 4 2x2 cross braces. When running WFO im turning between 3980 and 4000 RPMS. Boat runs very well and i'm extremely pleased with how it handles. on a side note, this boat is only .3 mph slower than my 1648 PD boat that was .125 bottom, and this boat has alot more stuff in it than the PD one.










Author:  bundy [ Sun Oct 18, 2009 6:29 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

sweet rig man congrats :D

Author:  Full Throttle [ Sun Oct 18, 2009 6:49 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Damn fine rig...... I think brother builds the nicest custom boat. I'm shore lovin mine!

Did you have him add the trim tab on the back of the transom? He didn't do mine that way.

Is that a pic of you or brother? If its you, you could pass for brother's brother. :lol:
Congrats!

Author:  jus10inla [ Sun Oct 18, 2009 7:32 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

thats @ brothers camp loox like..

Author:  OwenDickeson [ Sun Oct 18, 2009 7:35 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  Gatorpoint [ Mon Oct 19, 2009 8:56 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Looks good! Cant wait to hear your review!! Brotha builds a nice boat.

Author:  jett1414 [ Mon Oct 19, 2009 9:45 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Looks good man, I like that gas tank built in there. That marine 36 looks good too. Think it will break 30 :?:

Author:  Mitschke [ Mon Oct 19, 2009 9:48 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Nice look boat!

I also noticed the lack of the governor, and the multi wires for the 20/50 amp charging system...

Author:  Wilson [ Mon Oct 19, 2009 10:17 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Be careful tieing down your motor like that. I used to tie it down in a similar way, then was told not to by PD. Now I just tie the boat down to the trailer and bungie cord the PD handle so it doesn't go side to side.

Author:  basinhunter [ Mon Oct 19, 2009 1:47 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  mcnemar1982 [ Mon Oct 19, 2009 2:06 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

dang nice rig! :mrgreen:

Author:  Full Throttle [ Mon Oct 19, 2009 4:50 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  OwenDickeson [ Mon Oct 19, 2009 6:07 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  jett1414 [ Mon Oct 19, 2009 7:04 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Owem, what happened to 30.2? You and Brotha cant screw with me like that, it makes my head spin. :x

Author:  OwenDickeson [ Mon Oct 19, 2009 8:19 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  Wilson [ Mon Oct 19, 2009 10:21 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Buy some Boat Buckles for your trailer. They are one of my favorite additions that I have made.

Author:  D.T. [ Tue Oct 20, 2009 7:25 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Man I seen you this weekend in Breaux Bridge pulling that boat, you passed right in front of my mother in laws. Was about to post on here to see who it was for. Nice boat.

Author:  BROOKS [ Wed Oct 21, 2009 7:47 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Nice !!! Good fo you and tell Brother nice job !!! :D Dang good lookin' boathull !!!!

Who did the paint ?

Author:  OwenDickeson [ Wed Oct 21, 2009 11:37 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

camo designs

Author:  yak [ Thu Oct 22, 2009 9:06 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

good lookin set up ;)

Author:  J Wales [ Thu Oct 22, 2009 12:17 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Nice looking boat.

Author:  captmike [ Sun Nov 01, 2009 5:43 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Question, will the galvanized drain plug corrode in salt water?

Author:  DeathMetalDukk [ Sun Nov 01, 2009 7:39 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Nice rig. I noticed the beefed up crimps. 8-)

Author:  OwenDickeson [ Sun Nov 01, 2009 10:18 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  ricabernathy [ Fri Dec 11, 2009 11:40 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

hahaha i thought i recognised the girl in ur pic owen haha

Author:  Tollett [ Tue Dec 29, 2009 8:12 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

What's the price tag on that boat? Just the boat. More expensive than a PD or GatorTail?

Author:  eazy89 [ Sun Jan 31, 2010 4:49 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

I want one of those...Do you have a contact number to brothers boats? Do they have a website?

Author:  OwenDickeson [ Sun Jan 31, 2010 7:57 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

no website...just a coonass that builds boats. :D 337-592-0200 leave him a message.

Author:  Mudhead [ Mon Feb 15, 2010 10:32 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

One piece hull or 3 piece?

Author:  Gatorpoint [ Mon Feb 15, 2010 11:22 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD


Author:  B.M. Barrelcooker [ Mon Feb 22, 2010 8:18 am ]
Post subject:  Re: 1848 Brother Boat with 36 PD

that is a nice lookin rig

Author:  Old School [ Tue Feb 23, 2010 10:11 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

Boat is for sale on Louisiana Sportsman classified section

Author:  OwenDickeson [ Tue Feb 23, 2010 11:09 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

sho nuff, everythings for sale for the right price ;)

Author:  LA Mudder [ Wed Mar 24, 2010 8:24 pm ]
Post subject:  Re: 1848 Brother Boat with 36 PD

that there is a very nice lookin rig

Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/