MM Brand: Pro Drive 36, Hydraulic Reverse, Trim and Tilt, Remote
Mods: Performance V Twins 45 Mag recipe- Cam, Lifters, Con Rods, Pistons, SS Valves, 3 angle Valve Job, Rockers and Push Rods, High Rev Coils, BPS Q Muffler
Boat Brand: Cajun Performance 1752, 20 inch sides, and .125 construction throughout
Boat Lay Out: Side Console, Hunt Deck, Rear Deck and Storage, Extended Deck, 8 inch Cat Walks
Extras: Dual Deep cycle Batteries (one in rear storage and one in the bow), Battery Charging System, Hydro Turf Throughout, Gator Glide, two 6 gallon Gas Tanks, 4000lb Winch, HID Lights, Shark Eyes, Trolling Motor bracket and Plug, Mud Buddy Shaggy Blind plus a lot of extra grass, Paint Job by Cajun Camo.

Speeds Shallow Water: N/A yet...
Speeds Deep water: 28.2 into 1 foot rollers and 29.6 with them. Rough...
Total Boat Load: Everything above- Plus Me 175, socket set, life vests etc...

Jeremy and Daniel at Cajun Performance were a pleasure to deal with , and just straight up good guys. They have a lot of pride in their work, and it comes out in the quality product they put out. Daniel puts down some of the best welds I have seen. I had the hull rigged by Pro Drive, and these guys were awesome as well. I spent two days it their shop working along side these guys and they were awesome. There attention to detail, and mindset that anything can be done, and it should be done right was no surprise but awesome to see!

A couple of follow of items that are still in the works are a rack for my lay out boat that will be installed in the catwalks, and two more seat bases.

The work PVT did on the engine combined with the High Rev Coils seems to be a great combo. The motor idles at around 1100 and is just dead smooth. The acceleration is solid and powerful. I will be loading it down this weekend with three guys, tow lay out boats, and a normal layout spread,,,,we will see how she does. The engine wants to run around 4350-4450 as the sweet spot...I haven't spent enough time yet to really get it dialed in, and I was taking at easy as the motor is still breaking in.

I will report back when I spend more time with the rig, but I couldn't be happier with the build.

More...I need to take some good pictures, as all of theses were taken with my phone...

damn sp is the a range rover i see?
i like the boat. nice work sko

Very nice!

I should also add that David at Cajun Camo was a pleasure to work with as well. He worked with me to customize his base color for the Nat Gear, sent me samples, installed the hydroturf, and sprayed the Gator Glide! I would absolutely recommend David as well...

Very nice rig, I would think it should run a little faster with all of those mods though.

Thx man. I think the speeds are about right. My typical load is the equivalent to most guys running with 2-3 guys my size. If I took the blind off it would be 29 plus into 1 foot rollers deep water. With everything else I have in the boat, that is pretty solid. If it was just a plain tiller open hull, my guess 31-33. These mods are more for load carrying than top end speed though. My last rig had a cam, pushrods, IM heads,SS valves, rockers and a Mikuni and the numbers were identical, if not a little lower. It was pretty rough on the lake. Like I said, I have only run it for about 30 minutes, so i will get it dialed in as well.

Thanks SP

NIce camo job, but I do have to say, that BPS exhaust is really shinny. Hope you cover it up when hunting. If birds start flaring, that would be a great reason.
Nice setup.

very nice

I finally took some more pictures...

more

more

more...

Very Nice Rig!! Looks like you put alot of thought into the rigging!!

Very nice Newton! Did you get it bloody yet?

damn nice rig

That's a fine-ass boat you got there! Congrats!!

Nice rig bro! Happy hunting!

the more I see Jeremys hulls the more I want one!.... DAMMIT

SP I'm gonna be lookin forward to seeing this rig on the Kiss chain bro so if you are at the ramp i'm coming to Check it out , though I might have seen you the Last sunday of the split VERY nice lookin boat.

Love the layout. Exactly what I want in my next rig. Just probably going to stay tiller. An Xtreme with this layout would be sweet!!