| Author |
Message |
|
Muddrunner958
MMT Pro Member
Joined: Thu Jul 05, 2012 4:21 pm
Posts: 112
|
 Boat speeds My buddy is running a 1438 with mudbuddy 23
What speeds should he be gating out of it?
_________________
Hunting, fishing, family and friends is all you need to make life good!!!
17x48 with a GTR 35 Stage 2
|
| Wed May 29, 2013 9:57 am |
|
|
|
CCC
MMT 1000 Club
Joined: Sun Jan 01, 2012 9:25 am
Posts: 1685
|
Re: Boat speeds It's should fly with 1 person if its not plowing too bad
|
| Wed May 29, 2013 10:06 am |
|
|
|
tailfisher17t
MMT Pro Member
Joined: Wed Dec 29, 2010 6:47 pm
Posts: 328
|
Re: Boat speeds Yup cause it will sink to da bottom!
_________________
Team Total ASalt
Mossy Oak Pro Staff
1854Gator Traxs w/HD pushed by a MB 5000.
Ams wrote:
If assholes could fly this place would be an airport
|
| Wed May 29, 2013 12:34 pm |
|
|
|
tailfisher17t
MMT Pro Member
Joined: Wed Dec 29, 2010 6:47 pm
Posts: 328
|
Re: Boat speeds Kinda like sex with your best friends girl!
_________________
Team Total ASalt
Mossy Oak Pro Staff
1854Gator Traxs w/HD pushed by a MB 5000.
Ams wrote:
If assholes could fly this place would be an airport
|
| Wed May 29, 2013 12:40 pm |
|
|
|
Muddrunner958
MMT Pro Member
Joined: Thu Jul 05, 2012 4:21 pm
Posts: 112
|
Re: Boat speeds Iol and yea I have that problem with my boat
Can't slow down fast or I get bout 2 foot of water in boat
_________________
Hunting, fishing, family and friends is all you need to make life good!!!
17x48 with a GTR 35 Stage 2
|
| Wed May 29, 2013 1:36 pm |
|
|
|
Muddrunner958
MMT Pro Member
Joined: Thu Jul 05, 2012 4:21 pm
Posts: 112
|
Re: Boat speeds Gotcha
_________________
Hunting, fishing, family and friends is all you need to make life good!!!
17x48 with a GTR 35 Stage 2
|
| Wed May 29, 2013 3:53 pm |
|
|
|
rudyeng
MMT Addict
Joined: Mon Jul 30, 2012 7:40 pm
Posts: 596
|
Re: Boat speeds I had a 1442 w/ 23 Dixie. To remedy the water over transom & CG issues I added homemade trim tabs. In my case it worked great.
You could stop at WOT. No water issues. Used scrap stainless my welder had. Bent it 90 degrees. Measured 10" wide x 6" long (both sides)
Hope that helps.
|
| Wed May 29, 2013 5:36 pm |
|
|
|
Muddrunner958
MMT Pro Member
Joined: Thu Jul 05, 2012 4:21 pm
Posts: 112
|
Re: Boat speeds Did u get more speed with the tabs on?
_________________
Hunting, fishing, family and friends is all you need to make life good!!!
17x48 with a GTR 35 Stage 2
|
| Thu May 30, 2013 5:32 pm |
|
|
|
