| It is currently Sun Jun 22, 2025 5:40 pm |
|
Page 1 of 1 |
[ 12 posts ] |
| Print view | Previous topic | Next topic |
gaskets
| Author | Message |
|---|---|
|
MMT Addict
Joined: Wed Feb 18, 2009 9:31 pm Posts: 584 Location: Meraux, LA 
|
 gasketscan anyone tell me a good website where theyr buying valve cover gaskets and oil filters for 29,31,and 35 vanguards.
_________________ 17x54 custom CC with stage 3 GTR. |
| Fri May 22, 2009 8:26 pm |
|
|
|
|
MMT Elite Member  Joined: Tue Jan 13, 2009 6:08 pm Posts: 5282 Location: Meraux,La.
|
Re: gaskets Darrel I just use the filters from walmart,as far as the valve cover gaskets never had to get any.
What the hell you doing to that thing? |
| Fri May 22, 2009 10:38 pm |
|
|
|
|
MMT Member  Joined: Thu May 21, 2009 9:52 am Posts: 18
|
Re: gaskets Go to any Briggs Stratton dealer, (lawnmower etc.).
They have the original filters and the valve cover gakets. _________________ IF IT FLY, IT DIES !!!!!!!!!! |
| Sat May 23, 2009 4:15 am |
|
|
|
|
MMT Elite Member  Joined: Tue Jan 13, 2009 8:02 pm Posts: 6243 Location: Bossier City
|
Re: gaskets Good luck finding anyone that stocks parts for the big block Briggs. Most will have to order the parts themselves so you might as well have parts sent to your house. I used these folks for a few things I have needed so far. I use the stock filters so Lowes, Home Depot or Walmart will have the them along with plugs.
http://www.outdoordistributors.com/Brig ... smain.html _________________ 18x48 Charles Leonard / 36PD "I do think there is a Squatch in these woods"!!!!! |
| Sat May 23, 2009 7:06 am |
|
|
|
|
MMT Addict
Joined: Wed Feb 18, 2009 9:31 pm Posts: 584 Location: Meraux, LA
|
Re: gaskets _________________ 17x54 custom CC with stage 3 GTR. |
| Sat May 23, 2009 8:09 am |
|
|
|
|
MMT Elite Member Joined: Tue Jan 13, 2009 6:08 pm Posts: 5282 Location: Meraux,La.
|
Re: gaskets Ya goin deep now
 |
| Sat May 23, 2009 8:39 am |
|
|
|
|
MMT Addict
Joined: Wed Feb 18, 2009 9:31 pm Posts: 584 Location: Meraux, LA
|
Re: gaskets i know ill regret tinkering with it because once you start it never stops. hopefully ill be up again in a week or so then we can go make a run
_________________ 17x54 custom CC with stage 3 GTR. |
| Sat May 23, 2009 8:59 am |
|
|
|
|
MMT 1000 Club  Joined: Wed Feb 04, 2009 7:50 pm Posts: 3833 Location: Old East Dallas, Texas
|
Re: gaskets That carb kit won't do you much good if your compression is that lopsided. Get your heads fixed.
_________________ Excel 1851F4 w/ MB35HD+R CDI with a little bit of this and little bit of that |
| Sat May 23, 2009 10:06 am |
|
|
|
|
MMT Addict
Joined: Wed Feb 18, 2009 9:31 pm Posts: 584 Location: Meraux, LA
|
Re: gaskets no, those numbers are for 2 motors, one motor (sd) has 90 psi in both cylinders. and the lt has 140 in each cylinder. i did the carb 1st to try to gain a couple top speed mph since im only getting about 26 tops at 3600-3650 or so rpm.
_________________ 17x54 custom CC with stage 3 GTR. |
| Sat May 23, 2009 12:00 pm |
|
|
|
|
MMT Pro Member
Joined: Fri Feb 13, 2009 12:06 am Posts: 260
|
Re: gaskets |
| Sat May 23, 2009 12:01 pm |
|
|
|
|
MMT 1000 Club Joined: Wed Feb 04, 2009 7:50 pm Posts: 3833 Location: Old East Dallas, Texas
|
Re: gaskets _________________ Excel 1851F4 w/ MB35HD+R CDI with a little bit of this and little bit of that |
| Sun May 24, 2009 3:43 am |
|
|
|
|
MMT Addict
Joined: Wed Feb 18, 2009 9:31 pm Posts: 584 Location: Meraux, LA
|
Re: gaskets sure is, wot out water i get 4100 but in water w/ 1 person i average 3500, i was lucky to get it to 3600-3650 a few times but when i do trim it up that much i start losing speed
_________________ 17x54 custom CC with stage 3 GTR. |
| Sun May 24, 2009 7:40 am |
|
|
|
|
|
Page 1 of 1 |
[ 12 posts ] |
|
All times are UTC - 6 hours |
Who is online |
Users browsing this forum: No registered users and 139 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |