|
|
FAQ
• Login
|
|
It is currently Wed Jul 16, 2025 4:07 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
PD HYDRO TRIM INSTALLATION
| Author |
Message |
|
canvasbackdrake
MMT Pro Member
Joined: Mon Mar 22, 2010 8:44 pm
Posts: 140
Location: Pearland, TX
|
 PD HYDRO TRIM INSTALLATION NEED A LITTLE HELP HERE, do you think MY X2 PRO DRIVE BOAT transom has enough room to install the pump without offsetting it to the side.Is a 2009 model. Since I don't have a brace in the middle I was told I may have to offset or weld one. Thanks for the help.
You do not have the required permissions to view the files attached to this post.
|
| Thu Sep 29, 2011 4:51 pm |
|
|
|
cb5331
MMT Super Elite Member
Joined: Fri Dec 18, 2009 8:10 pm
Posts: 16915
Location: Rowlett, TX
|
Re: PD HYDRO TRIM INSTALLATION That brace looks low enough, but it's hard to tell. We had to offset on my dad's last boat, but the hoses they came with were long enough. Wasn't a big deal.
|
| Thu Sep 29, 2011 4:59 pm |
|
|
|
greg f
MMT Pro Member
Joined: Sat Feb 05, 2011 10:02 pm
Posts: 490
Location: Mexifornia
|
Re: PD HYDRO TRIM INSTALLATION looks like you have room.
|
| Thu Sep 29, 2011 5:03 pm |
|
|
|
meterman3
MMT 1000 Club
Joined: Mon Dec 21, 2009 6:25 pm
Posts: 1407
|
Re: PD HYDRO TRIM INSTALLATION i would try to put it under the corner brace out of the weather and sun plastic will last a lot longer that way
_________________
driving a gd in ur lake
and i aprove this message
|
| Thu Sep 29, 2011 5:06 pm |
|
|
|
the gator
MMT Pro Member
Joined: Tue Sep 06, 2011 5:23 pm
Posts: 190
Location: Patterson,LA
|
Re: PD HYDRO TRIM INSTALLATION yes anyone of the vertical channels is where they install them.
_________________
35gtr Stage 1 On 19'3"x46" Mad man Hull going Places far and beyond
|
| Thu Sep 29, 2011 6:29 pm |
|
|
|
canvasbackdrake
MMT Pro Member
Joined: Mon Mar 22, 2010 8:44 pm
Posts: 140
Location: Pearland, TX
|
Re: PD HYDRO TRIM INSTALLATION Does the pump just install on the PD bracket where the pre drilled holes are at? Or do you also bolt it on the boat? If it needs to be offset do I use self tapping screws to put on the brace. Thanks for the help again.
|
| Thu Sep 29, 2011 8:56 pm |
|
|
|
POKER1
MMT Elite Member
Joined: Tue Jan 13, 2009 8:02 pm
Posts: 6243
Location: Bossier City
|
Re: PD HYDRO TRIM INSTALLATION
_________________
18x48 Charles Leonard / 36PD
"I do think there is a Squatch in these woods"!!!!!
|
| Thu Sep 29, 2011 9:09 pm |
|
|
|
canvasbackdrake
MMT Pro Member
Joined: Mon Mar 22, 2010 8:44 pm
Posts: 140
Location: Pearland, TX
|
Re: PD HYDRO TRIM INSTALLATION I got a measurement of 13.5 in of clearance from where you bolt the trim on the motor to where the middle brace starts (see the pics).Can someone give me a measurement of the entire unit. I think I was told I needed a 12 inch clearance? I just want to verify, before I ordered it, thanks again!
|
| Fri Sep 30, 2011 8:34 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 96 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
