|
|
FAQ
• Login
|
|
It is currently Wed Jul 16, 2025 9:19 am
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Polling platform height requirment?
| Author |
Message |
|
JGUT
MMT Pro Member
Joined: Sun Jan 16, 2011 6:00 pm
Posts: 58
Location: Kemah, Texas
|
 Polling platform height requirment? looking at getting a polling platform made but im not sure how tall to make it so it will clear all brands of surface drives. thanks in advance for any info.
_________________
23HP GO-DEVIL longtail pushing a 1750 Mike Kliebert custom
|
| Fri Oct 07, 2011 1:10 pm |
|
|
|
MaXXis85
MMT Elite Member
Joined: Wed Jan 14, 2009 7:23 am
Posts: 6233
Location: Tarkington, TX
|
Re: Polling platform height requirment? A Tape measure will definately have the answer for you!
_________________
Bayou Surface Drive
337-351-0362
Tarkington, TX 77327
|
| Fri Oct 07, 2011 1:52 pm |
|
|
|
JGUT
MMT Pro Member
Joined: Sun Jan 16, 2011 6:00 pm
Posts: 58
Location: Kemah, Texas
|
Re: Polling platform height requirment? wow great advise! dont you think if i had a surface drive to measure i would have done it.
_________________
23HP GO-DEVIL longtail pushing a 1750 Mike Kliebert custom
|
| Sun Oct 09, 2011 5:22 pm |
|
|
|
Pick
MMT Member
Joined: Wed Aug 10, 2011 8:14 am
Posts: 9
Location: New Orleans, La
|
Re: Polling platform height requirment? I'm running a 38" tall platform over my GTR 35 and have plenty of clearance over my aftermarket carb which raised the motor height a few inches. I like the height, but probably could have gotten away with 34" which would make it easier to get on an off and you could use a little bit shorter push pole(I use a 22'). Those heights are measured from the transom.
_________________
17'3" Cat 5 Center Console with a GTR 35 with Cam, Rockers, Pushrods, Black Death, Mikuni, K&N, BPS Twins
|
| Sun Oct 09, 2011 5:28 pm |
|
|
|
Gigafowl
MMT Elite Member
Joined: Tue Jan 13, 2009 7:19 pm
Posts: 6441
Location: Trinity Bay - Texas
|
Re: Polling platform height requirment? The GDSD is roughly 4" to 5" taller than your LT....
What measurement do you want mine is handy ???
On my GD lo transom - 50" from floor to bottom of platform
35" from transom to bottom of platform - note platform is also
made to work with tall transom - so there is more clearance
than needed on the lo or std transom design....
1" square tubing is below the bottom of the platform
so deduct 1" when calculating clearance
_________________
Eat - Sleep - Hunt ! ! !
"It is good to have an end to journey toward; but
it is the journey that matters, in the end."
|
| Sun Oct 09, 2011 5:34 pm |
|
|
|
CAJUN OUTLAW
MMT 1000 Club
Joined: Thu Jan 22, 2009 10:37 pm
Posts: 2577
|
Re: Polling platform height requirment? go with the measurements from the gtr guy,34",they should all clear if the tall-ass gtr clears.
|
| Sun Oct 09, 2011 10:43 pm |
|
|
|
JGUT
MMT Pro Member
Joined: Sun Jan 16, 2011 6:00 pm
Posts: 58
Location: Kemah, Texas
|
Re: Polling platform height requirment? thanks guys appreciate the info.
_________________
23HP GO-DEVIL longtail pushing a 1750 Mike Kliebert custom
|
| Mon Oct 10, 2011 8:32 am |
|
|
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 84 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
