| Author |
Message |
|
SmokeEater829
MMT 1000 Club
Joined: Sat Jun 13, 2009 8:48 pm
Posts: 1830
Location: Belle Chasse, LA
|
 Installing new High rev coils Well, my new coils came in this week. Working on the install now. Got everything off of the motor, and waiting for a buddy to bring me some feeler gauges. Mine have turned into a ball of rust. The new coils are labeled Right and Left. Is this right and left as you are looking at the motor or as the motor sits facing into the boat?
I'm sure its a stupid question, but there is no clear answer that I could find.
_________________
Mud Buddy 4500 Black Death hauling the Uncle J 18x58
|
| Sun Feb 26, 2012 5:20 pm |
|
|
|
Beadlejuicejr
MMT 1000 Club
Joined: Tue Nov 02, 2010 7:11 pm
Posts: 1435
Location: Bayou vista, Louisiana
|
Re: Installing new High rev coils Use a business card it works too make sure set them on the magnet too.
_________________
stage 3 GTR screaming behind the 1848 Garrett Pearce special. GET YOU SOME!
|
| Sun Feb 26, 2012 5:52 pm |
|
|
|
SmokeEater829
MMT 1000 Club
Joined: Sat Jun 13, 2009 8:48 pm
Posts: 1830
Location: Belle Chasse, LA
|
Installing new High rev coils Has anyone that has installed them found that the wire to the plug is too short? I don't think I'm going to be able to make the one on the left side (opposite side from tiller arm) reach the plug unless I bend the wire into a 90
_________________
Mud Buddy 4500 Black Death hauling the Uncle J 18x58
|
| Sun Feb 26, 2012 6:21 pm |
|
|
|
swampbilly
MMT 1000 Club
Joined: Fri Oct 07, 2011 6:08 pm
Posts: 1054
Location: Dam-b, Texas
|
Re: Installing new High rev coils
_________________
pd36 fpr 1754 cc rig
|
| Sun Feb 26, 2012 6:46 pm |
|
|
|
SmokeEater829
MMT 1000 Club
Joined: Sat Jun 13, 2009 8:48 pm
Posts: 1830
Location: Belle Chasse, LA
|
Re: Installing new High rev coils Can anyone else comment on this?
_________________
Mud Buddy 4500 Black Death hauling the Uncle J 18x58
|
| Sun Feb 26, 2012 9:33 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils I just put mine on a few days ago nd they worked fine. The plug wires face out, the kill wire has to be re routed to reach the new coil. And x2 on the business card for gap. So just put em to where the wires face out and you should be fine.
|
| Sun Feb 26, 2012 10:08 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils Oh and the left and right is looking at the front of the motor.
|
| Sun Feb 26, 2012 10:09 pm |
|
|
|
SmokeEater829
MMT 1000 Club
Joined: Sat Jun 13, 2009 8:48 pm
Posts: 1830
Location: Belle Chasse, LA
|
Installing new High rev coils Thanks Rod. I ended up putting my stock ones back on. I'm gonna look into that tomorrow.
_________________
Mud Buddy 4500 Black Death hauling the Uncle J 18x58
|
| Sun Feb 26, 2012 10:18 pm |
|
|
|
SmokeEater829
MMT 1000 Club
Joined: Sat Jun 13, 2009 8:48 pm
Posts: 1830
Location: Belle Chasse, LA
|
Installing new High rev coils I'm just posting this on here to let anyone else who might run into this issue. The sticker and the stamping / engraving on the coil were opposite. The sticker said "this side out". Under the sticker, the coil was stamped "this side in". I never thought to peel off the sticker and check the coil. Hope this helps someone.
_________________
Mud Buddy 4500 Black Death hauling the Uncle J 18x58
|
| Tue Feb 28, 2012 6:20 am |
|
|
|
odass
MMT 1000 Club
Joined: Tue Aug 02, 2011 5:30 pm
Posts: 1928
|
Re: Installing new High rev coils Hey autogate how you like them coils?
_________________
Dead Fowl Custom 1954hd with a GTR
|
| Tue Feb 28, 2012 11:51 am |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils Very good money spent. Almost like adding a gear to my motor.
|
| Tue Feb 28, 2012 11:55 am |
|
|
|
odass
MMT 1000 Club
Joined: Tue Aug 02, 2011 5:30 pm
Posts: 1928
|
Re: Installing new High rev coils Cool did you get a GPS on it
_________________
Dead Fowl Custom 1954hd with a GTR
|
| Tue Feb 28, 2012 1:02 pm |
|
|
|
schmitt
MMT 1000 Club
Joined: Fri Jun 25, 2010 3:33 pm
Posts: 1177
Location: WI
|
Re: Installing new High rev coils
_________________
1848 DeadFowl pushed by a Stage 4 Delta powered MB HDR (JBP dusting)
|
| Tue Feb 28, 2012 1:36 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils All over limiter before. This past weekend ran 33.5 with 12 gal gas, me and my wife, deep water.
|
| Tue Feb 28, 2012 2:04 pm |
|
|
|
schmitt
MMT 1000 Club
Joined: Fri Jun 25, 2010 3:33 pm
Posts: 1177
Location: WI
|
Re: Installing new High rev coils ok thats what I thought. These coils wont help guy's that dont have the added power to get the rpm's up over 4300. Just put mine on and waiting to put the cam in! Cant wait to see what it will do
_________________
1848 DeadFowl pushed by a Stage 4 Delta powered MB HDR (JBP dusting)
|
| Tue Feb 28, 2012 2:17 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils Yeah they won't make a difference if you couldn't hit limiter before.
|
| Tue Feb 28, 2012 2:18 pm |
|
|
|
odass
MMT 1000 Club
Joined: Tue Aug 02, 2011 5:30 pm
Posts: 1928
|
Re: Installing new High rev coils
_________________
Dead Fowl Custom 1954hd with a GTR
|
| Tue Feb 28, 2012 2:54 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Installing new High rev coils Yep. Getting prop reworked
|
| Tue Feb 28, 2012 3:15 pm |
|
|
|
odass
MMT 1000 Club
Joined: Tue Aug 02, 2011 5:30 pm
Posts: 1928
|
Re: Installing new High rev coils Do you have any internal work done? Are you going to a 12x12
_________________
Dead Fowl Custom 1954hd with a GTR
|
| Tue Feb 28, 2012 6:04 pm |
|
|
|
autogateman
MMT Sponsor
Joined: Thu Sep 16, 2010 10:32 pm
Posts: 4036
Location: Gonzales La
|
Re: Installing new High rev coils IM heads, bps cam, single mikuni, crossover exhaust, coils. going to a 12x12 or 12x 11.5
|
| Tue Feb 28, 2012 6:22 pm |
|
|
|
swampbilly
MMT 1000 Club
Joined: Fri Oct 07, 2011 6:08 pm
Posts: 1054
Location: Dam-b, Texas
|
Re: Installing new High rev coils
_________________
pd36 fpr 1754 cc rig
|
| Tue Feb 28, 2012 6:59 pm |
|
|
|
