| Author |
Message |
|
mudbuddyLT25hp
MMT Member
Joined: Thu Sep 13, 2012 9:58 pm
Posts: 10
|
 mud buddy 45hp cam questions can some one tell me how the mudbuddy 45 mag holds up with lower gears and cams?
|
| Mon Sep 17, 2012 6:31 pm |
|
|
|
270Handiman
MMT 1000 Club
Joined: Thu Dec 29, 2011 10:46 pm
Posts: 2342
Location: Mandeville, LA
|
Re: mud buddy 45hp cam questions Do what?
|
| Mon Sep 17, 2012 6:44 pm |
|
|
|
mudbuddyLT25hp
MMT Member
Joined: Thu Sep 13, 2012 9:58 pm
Posts: 10
|
Re: mud buddy 45hp cam questions Is that ''do what" to the gears? cuz thats what i was thinking when the guy told me it had gears in it. im kinda new at this whole surface drive deal
|
| Mon Sep 17, 2012 7:07 pm |
|
|
|
schmitt
MMT 1000 Club
Joined: Fri Jun 25, 2010 3:33 pm
Posts: 1177
Location: WI
|
Re: mud buddy 45hp cam questions Yeah u may have to explain that a bit better. They have a gear off the motor and a gear on the lower prop shaft that the belt goes around. The cam shaft is inside the motor.
_________________
1848 DeadFowl pushed by a Stage 4 Delta powered MB HDR (JBP dusting)
|
| Mon Sep 17, 2012 8:04 pm |
|
|
|
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm
Posts: 1018
Location: DA HAVEN FL,
|
Re: mud buddy 45hp cam questions
_________________
EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
| Mon Sep 17, 2012 8:08 pm |
|
|
|
schmitt
MMT 1000 Club
Joined: Fri Jun 25, 2010 3:33 pm
Posts: 1177
Location: WI
|
Re: mud buddy 45hp cam questions
_________________
1848 DeadFowl pushed by a Stage 4 Delta powered MB HDR (JBP dusting)
|
| Mon Sep 17, 2012 8:13 pm |
|
|
|
mudbuddyLT25hp
MMT Member
Joined: Thu Sep 13, 2012 9:58 pm
Posts: 10
|
Re: mud buddy 45hp cam questions ha i no the cam is in side the motor! but this guys boat im looking at he told me that it had low end gears. i just never have heard of that.
|
| Mon Sep 17, 2012 8:14 pm |
|
|
|
schmitt
MMT 1000 Club
Joined: Fri Jun 25, 2010 3:33 pm
Posts: 1177
Location: WI
|
Re: mud buddy 45hp cam questions Well with the Mudbuddy u can change gears to your liking, If u want low end, top end or what not. Not hard to do
_________________
1848 DeadFowl pushed by a Stage 4 Delta powered MB HDR (JBP dusting)
|
| Mon Sep 17, 2012 8:20 pm |
|
|
|
270Handiman
MMT 1000 Club
Joined: Thu Dec 29, 2011 10:46 pm
Posts: 2342
Location: Mandeville, LA
|
Re: mud buddy 45hp cam questions Ok, if it has a performance cam (not cams, only one in there), that is potentially a good thing. The gearing should be set to get the most performance possible with a particular load. If he's telling you it's geared low, I'm assuming he was carrying a big load with it or something. The bad news is that with a light load you want get any speed out of it, but as mentioned above, it's fairly east to swap the gears if needed.
|
| Mon Sep 17, 2012 10:14 pm |
|
|
|
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm
Posts: 1018
Location: DA HAVEN FL,
|
Re: mud buddy 45hp cam questions
_________________
EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
| Tue Sep 18, 2012 5:38 am |
|
|
|
