| Author |
Message |
|
duckbill
MMT Pro Member
Joined: Tue Mar 31, 2009 9:40 am
Posts: 238
Location: Dallas, Texas
|
 Pulling Flywheel - Help I need to pull the flywheel off my 23 vanguard. I've got all the shrouding off and am at the flywheel nut. What's the best way to get that thing off and back on when I re-assemble? Obviously the flywheel wants to spin when I turn the nut, so what's the best way to keep the flywheel from spinning so that I can get the nut off? Thanks for the help fellas.
_________________
1644 Go-Devil
2008 23 GDSD
|
| Wed Apr 21, 2010 8:40 pm |
|
|
|
Pooh Bear
MMT Addict
Joined: Wed Jan 14, 2009 10:43 pm
Posts: 612
Location: Everywhere.USA
|
Re: Pulling Flywheel - Help Use a large screwdriver (flatblade) to put a bind on the flywheel. Install the screwdriver between the case ,or studs against the middle of the flywheel teeth. I hope you can understand what Im meaning. Kinda hard to explain without pictures.
_________________
Don't mistake my kindness for weakness, my ability to look over things as ignorance - but make no mistake, when I've had enough, I'm Coming After you. Watch Your Back....lol
|
| Wed Apr 21, 2010 9:25 pm |
|
|
|
backwaterballer
MMT Addict
Joined: Sat Feb 21, 2009 9:39 pm
Posts: 715
Location: Pearland Tx
|
Re: Pulling Flywheel - Help I used an impact to bust the nut loose just a small jolt. Then just sprayed a lol wd 40 and tapped it with a rubber hammer and it slid off. Why you pullin the flywheel already.
_________________
23 hp gdlt pushin the 14ft NoWeld "aka" the black pearl
35 hp gdsd pushin a 16/60 go devil boat
|
| Wed Apr 21, 2010 9:33 pm |
|
|
|
deadbird8
MMT 1000 Club
Joined: Wed Feb 04, 2009 7:50 pm
Posts: 3833
Location: Old East Dallas, Texas
|
Re: Pulling Flywheel - Help I used a length of angle iron with holes drilled in it to attach to the face of the flywheel. It levers against the studs for the shroud to steady it while removing/installing.
_________________
Excel 1851F4 w/ MB35HD+R CDI with a little bit of this and little bit of that
|
| Thu Apr 22, 2010 5:02 am |
|
|
|
coondik
|
Re: Pulling Flywheel - Help go pick up a harmonic balancer puller from any of the "big chain" automotive stores.
|
| Thu Apr 22, 2010 9:14 am |
|
|
|
duckbill
MMT Pro Member
Joined: Tue Mar 31, 2009 9:40 am
Posts: 238
Location: Dallas, Texas
|
Re: Pulling Flywheel - Help By the time I saw coondik's message, I had already gone to Oreillys and rented a harmonic balancer puller. It worked like a charm and if I take it back within 48 hours I get my money back 
_________________
1644 Go-Devil
2008 23 GDSD
|
| Thu Apr 22, 2010 10:50 am |
|
|
|
bjg
MMT F.E.
Joined: Thu Jan 15, 2009 7:34 pm
Posts: 882
Location: Ahead of you, with a rubber band turning my prop!!
|
Re: Pulling Flywheel - Help I use a BF'ing Hammer with puller ingraved on it. It works well.
_________________
BUCK OFAMA
|
| Sat Apr 24, 2010 12:41 pm |
|
|
|
drake1
MMT Addict
Joined: Wed Jan 14, 2009 6:57 am
Posts: 659
|
Re: Pulling Flywheel - Help Watch Silk use two screw drivers and an airhammer. Comes off easy! 
|
| Sat Apr 24, 2010 4:35 pm |
|
|
|
brlcla
MMT F.E.
Joined: Tue Jan 13, 2009 5:11 pm
Posts: 955
Location: Lake Charles, LA
|
Re: Pulling Flywheel - Help Nah.... drake1.... Its kick the feet up, then watch Silk... Maybe grab a beer cause by the time you get up to get it he will be asking for his.
|
| Sat Apr 24, 2010 5:00 pm |
|
|
|
drake1
MMT Addict
Joined: Wed Jan 14, 2009 6:57 am
Posts: 659
|
Re: Pulling Flywheel - Help Where's the motor?
|
| Sat Apr 24, 2010 5:27 pm |
|
|
|
duckbill
MMT Pro Member
Joined: Tue Mar 31, 2009 9:40 am
Posts: 238
Location: Dallas, Texas
|
Re: Pulling Flywheel - Help where's what motor?
_________________
1644 Go-Devil
2008 23 GDSD
|
| Sat Apr 24, 2010 9:17 pm |
|
|
|
brlcla
MMT F.E.
Joined: Tue Jan 13, 2009 5:11 pm
Posts: 955
Location: Lake Charles, LA
|
Re: Pulling Flywheel - Help he was asking about my motor.... we are in the process of getting ready to build my Generac
|
| Sun Apr 25, 2010 9:38 am |
|
|
|
