| Author |
Message |
|
Quack N Stack
MMT 1000 Club
Joined: Sat Dec 15, 2012 9:43 pm
Posts: 2225
Location: Baytown, Tejas
|
 BPS throttle I ordered the BPS throttle leaver to put on my go devil and like a dummy i didnt measure anything to make sure it would fit. Well i went to put it on earlier and the throttle is just a tad bit to small to fit around the handle. Anyone else have this problem and how did you fix it? I came up with two options, either find a piece of pipe that the throttle will fit well over and cut it to length i need and cut the tiller shorter then weld the new smaller piece in it's place. Or i can get longer screws that will reach then tighten it up then heat the tiller pipe with a torch and tighten the screws until the metal bends or warps to fit the hole for the throttle.
Does this sound practical or a dumb idea?
|
| Tue Sep 09, 2014 7:27 pm |
|
|
|
msm8281
MMT Elite Member
Joined: Fri Oct 09, 2009 1:50 pm
Posts: 9673
Location: New Iberia, La.
|
Re: BPS throttle Use a dremel and open it up some . That's what I did.
|
| Tue Sep 09, 2014 7:29 pm |
|
|
|
Quack N Stack
MMT 1000 Club
Joined: Sat Dec 15, 2012 9:43 pm
Posts: 2225
Location: Baytown, Tejas
|
Re: BPS throttle
|
| Tue Sep 09, 2014 7:39 pm |
|
|
|
msm8281
MMT Elite Member
Joined: Fri Oct 09, 2009 1:50 pm
Posts: 9673
Location: New Iberia, La.
|
Re: BPS throttle Yes. Just keep taking material out till it fits. Careful its thin by one of the screw holes..
|
| Tue Sep 09, 2014 7:45 pm |
|
|
|
msm8281
MMT Elite Member
Joined: Fri Oct 09, 2009 1:50 pm
Posts: 9673
Location: New Iberia, La.
|
Re: BPS throttle I can take a picture of it Friday.
|
| Tue Sep 09, 2014 7:46 pm |
|
|
|
mudslut
MMT 1000 Club
Joined: Mon Dec 06, 2010 6:54 pm
Posts: 2061
Location: Natchitoches,La
|
Re: BPS throttle Yea use a dremel. That's what I did also.
Sent from my iPhone using Tapatalk
_________________
1646 Gatortail dragging a stage 1 GTR
|
| Tue Sep 09, 2014 7:49 pm |
|
|
|
Quack N Stack
MMT 1000 Club
Joined: Sat Dec 15, 2012 9:43 pm
Posts: 2225
Location: Baytown, Tejas
|
Re: BPS throttle Aight man thanks
|
| Tue Sep 09, 2014 7:50 pm |
|
|
|
DUCK HEARSE
MMT 1000 Club
Joined: Fri Apr 06, 2012 8:48 am
Posts: 3161
Location: Alabama
|
Re: BPS throttle
_________________
Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did do. So throw off the bowlines. Sail away from the safe harbor. Catch the trade winds in your sails. Explore. Dream. Discover.
- Mark Twain
|
| Tue Sep 09, 2014 7:57 pm |
|
|
|
Duck GORE
MMT Pro Member
Joined: Mon Feb 18, 2013 2:44 pm
Posts: 130
|
Re: BPS throttle You can just grind it bigger.
|
| Wed Sep 10, 2014 2:17 pm |
|
|
|
baron von
MMT 1000 Club
Joined: Tue Jan 21, 2014 2:52 pm
Posts: 2806
Location: Minnesota
|
Re: BPS throttle be sure to dip coat handle - makes for great gripping surface viewtopic.php?f=3&t=53952
_________________
that's going itch when it dries
|
| Wed Sep 10, 2014 3:25 pm |
|
|
|
msm8281
MMT Elite Member
Joined: Fri Oct 09, 2009 1:50 pm
Posts: 9673
Location: New Iberia, La.
|
Re: BPS throttle Take a little off everywhere, but take the most off here. Get rid of that hump.
Those screws are cheap. Make sure to use some grease or it will gall up.
You do not have the required permissions to view the files attached to this post.
|
| Wed Sep 10, 2014 5:24 pm |
|
|
|
baron von
MMT 1000 Club
Joined: Tue Jan 21, 2014 2:52 pm
Posts: 2806
Location: Minnesota
|
Re: BPS throttle nice - actual pictures
_________________
that's going itch when it dries
|
| Sun Sep 21, 2014 10:04 am |
|
|
|
Quackkillz
MMT Addict
Joined: Sun Dec 04, 2011 4:57 am
Posts: 535
Location: Bottom of da boot
|
Re: BPS throttle Just finished doing the same thing.
_________________
1648 weld bilt being followed by a 35 gtr
|
| Sun Sep 21, 2014 12:15 pm |
|
|
|
Pulpwood
MMT Pro Member
Joined: Thu Mar 01, 2012 12:23 pm
Posts: 215
|
Re: BPS throttle Had a machine shop take some off my handle. No modification to the throttle. $20 and was done.
|
| Tue Sep 23, 2014 6:18 am |
|
|
|
GatorDubea
MMT Pro Member
Joined: Fri Jun 07, 2013 12:56 pm
Posts: 491
Location: Alexandria, La
|
Re: BPS throttle can you use that throttle with a stock carb ?
_________________
07 16x50 w/ 07 35 gtr
|
| Tue Sep 23, 2014 6:28 am |
|
|
|
DmaxHunter
MMT 1000 Club
Joined: Wed Jan 18, 2012 7:21 pm
Posts: 2207
Location: North Alabama
|
Re: BPS throttle They make one for stock carbs
_________________
2014 PRODIGY 1754 (#19) 2014 5500 BAMF HDR RETRO SOLD
2010 Gator Tail Gator Series 18x54 pushed by a 2020 40GTRXD
|
| Tue Sep 23, 2014 6:32 am |
|
|
|
baron von
MMT 1000 Club
Joined: Tue Jan 21, 2014 2:52 pm
Posts: 2806
Location: Minnesota
|
Re: BPS throttle I don't see why you couldn't use with stock carb - i used stock cable with handle and PD EFI, I had to remove about 3/8" from housing on cable to get best results at the throttle body end of cable for the EFI
_________________
that's going itch when it dries
|
| Tue Sep 23, 2014 6:33 am |
|
|
|
Pulpwood
MMT Pro Member
Joined: Thu Mar 01, 2012 12:23 pm
Posts: 215
|
Re: BPS throttle The end was a little smaller, but I've had no problems with it coming out once I zip tied the black hosting to the motor and clamped it down with the clamp.
|
| Tue Sep 23, 2014 9:38 am |
|
|
|
